Tag: Reset

[1841] Reset Password / Config, ROMMON Upgrade and Software Upgrade on Cisco 1841

1.) Reset Password / Config

- Connect to the router via Serial Cable

- Power on the router, but send a break during the first 60 seconds of boot time to get to the rommon CLI

- enter confreg 0x2142 followed by a reset

- Router is booting up, as soon as it does enter the system configuration dialog, answer the question with no

- enable

- conf t

- config-register 0x2102

- exit

- wr mem (because I just want to overwrite the old config :)!)

2.) ROMMON Upgrade

- Get the latest / needed ROMMON upgrade from Cisco

- Copy it i.e. to your CF card via Card Reader, TFTP or other means

- Boot up the router and enter privleged / enable mode

- Enter the upgrade command: upgrade rom-monitor file flash:<Filename>

- Answer yes to get the process starteted

- After the upgrade the router will reload

3.) Software Upgrade

- Get the latest/needed image from Cisco

- Just copy it to the CF card via Card Reader, TFTP or other means

- Reload

HTC Universal

I found a "bricked" HTC Universal without - everything.
So I decided to piece it back together.
First thing to find was an USB Cable to recharge the battery.
Working is an normal Mini USB Cable, even tough the connector looks different.

After that, I found out that the HTC was a brick.
So to unbrick:

get mtty1.42.exe, enter bootloader mode , (Power + Light Bulb + Reset)

1. Stop Activesync USB connection
2. Uni : Reboot Bootloader then Connect USB
3. PC : Run mtty1.42.exe
4. Choose USB in "Port" (Reconnect if can't find/reconglize USB and try remove sim and sd card)
5. type : task 28 55aa
6. Press Enter
7. Cause DOC reformatted, so there's no rom in DOC ,try reflash any rom that you like .

For task 28 55aa in mtty success , will show the message (attachment )

DONE .
( http://forum.xda-developers.com/showpost.php?p=1097645&postcount=4 )

Under Windows Vista / 7 you need to use these drivers and stuff: http://forum.xda-developers.com/showthread.php?t=313001&highlight=flashing+vista

After that, we want to upgrade to a new rom.
I choose Maxstegis German Rom ( http://rom.maxstegi.de/index.php )
You should go for Version 6: http://rom.maxstegi.de/downloads.php?view=detail&df_id=12
And the Radio Image 1.18.00: http://rom.maxstegi.de/downloads.php?view=detail&df_id=14

Go into Bootloader Mode, start the Version 6 and it will upgrade.
Do not do anything to the Radio, we will change that soon...

Get the HTC Universal Unlock Tool to unlock your SIM:
http://buzzdev.com/m/files/view/HTC-Universal-SIM-unlock

Install Instructions:
1. Backup your phone (not necessary, but advisable).
2. Remove your SD Card.
3. Enter bootloader mode on your Phone. To do this, simultaneously hold down the backlight key (“bulb” key, next to volume key), the power key and soft reset the phone. Your phone screen should clear, and you will see very faint writing saying “serial”. Let go of buttons etc.
4. Connect your phone to your computer using the USB lead.
5. Run the MaUpgradeUt_noID.exe program – this will reflash your phone with necessary software required to enable the unlocker.
6. Wait patiently.
7. Once the MaUpgradeUt_noID.exe upgrade completes, soft reset your phone by pressing the soft reset button on the back of the device [if the flash has been successfully applied, you should see that you now have Radio version 0.00.00]
8. Allow your phone to reboot. Once it has, connect to your PC using Activesync, and copy the UNI_Unlock_v1.exe program onto your phone. Alternatively, copy it to an SD card and insert into your phone.
9. Run UNI_Unlock_v1.exe on your phone. Wait patiently.
10. Once the process completes, soft reset your phone.
11. Process is (hopefully) complete!
http://forum.gsmhosting.com/vbb/archive/t-316584.html

After that, boot loader Mode, flash the new Radio Firmware, after that you can reflash the ROM aswell, so to be sure that everything worked.
Thats it!

Enable Wireless G (802.11g) Support in HTC Universal Pocket PC Phone
HTC Universal also kwown as Qtek 9000, T-Mobile MDA Pro, Orange SPV M5000, O2 Xda Exec, i-mate JASJAR, Dopod 900, Vodafone v1640, Vodafone VPA IV, E-Plus PDA IV, Grundig GR980 and etc as it’s be re-branded and marketed by different vendors and network operators. One major disappointment and weakness of HTC Universal is it’s only support 802.11b-compatible technology, and thus unable to connec to WiFi G (802.11g) network.
It’s possible to make the HTC Universal based Pocket PC phone to compatible and able to connect to 802.11g-only access points by a registry tweak, but the speed would still be the same as 802.11b (11 Mbit/s).
The registry tweak is to change and add the following registry decimal values using a registry editing tool like the PHM Registry Editor at your HTC Universal based Pocket PC:

HKEY_LOCAL_MACHINE\COMM\TIACXWLN1\PARMS: dot11SupportedRateMask=1
HKEY_LOCAL_MACHINE\COMM\TIACXWLN1\PARMS: dot11SupportedRateMaskG=8

After adding and editing above registry key, soft-reset the device.
( http://www.mydigitallife.info/2006/08/01/enable-wireless-g-80211g-support-in-htc-universal-pocket-pc-phone/ )

If you ever need to hardreset your Device, press the two "-" Buttons on the Keyboard and the Reset Button while the Device is turned on. A screen will come up and ask for the reset, press... o to confirm.

Additional Tutorials: http://forum.xda-developers.com/showthread.php?t=549207

[79XX] Cisco IP Phone Factory Reset & Reboot

To Factory Reset a Cisco IP Phone do the following:
1. Press and hold #, disconnect and reconnect Power
2. The Phone will check through the Line LEDs, on an 7911 or similar it will just light up the both Menu Keys and the Reciever \ Handset LED - after that, let go of #
3. Enter following: 1 2 3 4 5 6 7 8 9 * 0 #
4. The Phone should start up and grab the latest config from your Callmanager

To just Reboot a Cisco IP Phone do following:
1. Go into any Menu
2. Enter #
3. Phone does reload
( 7940, 7960: Hold *,6,Settings )

To open up the Configuration on a Phone:
1. Go into Menu Setting
2. Enter **##

To Factory Reset and erase the firmware on a Cisco IP Phone do the following:
1. Press and hold #, disconnect and reconnect Power
2. The Phone will check through the Line LEDs, on an 7911 or similar it will just light up the both Menu Keys and the Reciever \ Handset LED - after that, let go of #
3. Enter following: 3 4 9 1 6 7 2 8 5 0 * #
4. The Phone should start up and grab the latest Firmware from your Callmanager

Snom 360 Update and Password Reset

WARNING, this is ONLY for Users on an Snom 360 with Firmware Revision 6.X.
If you got an different Revision the steps could be different.
Check out the Snom Wiki in that case ( http://wiki.snom.com/Firmware ).
Basically we just do reflash the Firmware with the same Revision again to erase data and passwords and unlock the Phone.
Than we do an automatic update to the latest release.

- Download the latest Snom 360 Firmware from the Snom Website for your Revision ( http://wiki.snom.com/Firmware/V6/Latest_Release )
- Download tftpd32 or an similar tftp Server
- Rename the Firmware to snom360.bin and upload it to the root Directory of the tftp Server
- Plug in the Network Port and Power to the Snom
- As the message "To Update by TFTP: Press Any Key" appears, press any key on the phone
- Enter valid IP Data for the Phone. Always press Next. I.e. the IP, the Subnet, the Gateway, DNS and the IP of your tfp Server.
- As you're finished, it will ask for this again and again, press Check Mark right beside the big X Button. The tfp Download will start. Don't unplug the phone during the Firmware Update. The Phone will automatically reboot after the flash is done.
- After this flash we have reset all data - including the passwords, so we now can press the Help Button on the phone and get the ip adress of the phone, connect to it by using an HTML Browser. But before you access the website, you need to enter the Administrative mode of the phone, otherwise you won't be able to set any setting or update the phone. So press the Settings Button and press "Administrative Mode" - password is 0000 on default. Press Check Mark to accept. Now access the Website.
- To update to version 7 Firmware (the latest Firmware, experimental) you need to go to the Advanced Tab, scroll down to Update. Set the Update Policy to "Update automatically" and the Setting URL to "http://provisioning.snom.com/update6to7/update_once.php". Press Save and Reboot, Accept with Yes. The Phone will Reboot.
- After the reboot, the phone will access the internet and check automatically for an update, download it and start flashing. It will reboot serval times, don't power it off until its done. It should take something like 10 Minutes or more, depending on your Internet connection. If it doesn't reboot anymore and does show the normal menu for longer than half an minute you can consider it ok.
- You can now create Identitys (Profiles) for your Sip / VoIP Accounts and reregister them via the Webinterface.

Astaro Security Gateway v7 Factory Reset

Access to SSH or console with root passwords:

/etc/init.d/factoryreset reset
No Access to SSH or root passwords are lost:

Connect a keyboard and monitor to the system.
Wait for boot prompt
Enter:
boot: default factoryreset

After that you can go to your during the installation definied IP like: https://192.168.0.1

Alternativ:

1. Boot on the ASG from a Knoppix CD
2. Login as root
3. Mount the root partition of the ASG with: mount –t ext3 /dev/sda7 /mnt
4. Go to the config on the ASG: cd /mnt/etc/wfe/conf/; vim setting
5. Change reset_pwd = 0 to reset_pwd = 1
6. Save
7. Run cd /; umount /mnt; reboot
8. Access the install IP